The TS-DIO24 is an 8-bit PC/104 expansion board that provides 24 digital I/O points. The I/O connector is an Opto-22 compatible interface that provides 16 I/O points configurable as input or output (24 mA as outputs) as well as 4 dedicated outputs capable of driving 48 mA and 4 dedicated outputs capable of sinking 1 Amp. The PC/104 interface decodes as registers in I/O space, the address is jumper selectable.
- 24 Digital I/O points
- Opto-22 compatible 50 pin connector
- 4 dedicated 48 mA ouputs, 4 dedicated 1 Amp outputs
- 16 programmable I/O points
- I/O address jumper selectable
- 4 interrupt capable inputs
- Up to 4 boards in a single system.
2 Hardware Configuration
|I/O Point Name||I/O Pin #||Ground Pin #||Signal Type|
|C7||1||2|| Port C
Input: TTL input (4.7k Ω pullup to +5vdc) (bits0-3 interrupt capable)
|B7||17||18|| Port B
Input: TTL input (4.7k Ω pullup to +5V)
|A7||33||34|| Port A
Output only: 1 Amp sink (open-drain 30V tolerant)
|A3||41||42|| Port A
Output only: 48 mA output (0-5V output drive)
|5V power||49||50||Auxiliary power protected by 750 mA Poly-Fuse|
|Note:||Transient suppression diodes required when driving inductive loads.|
|I/O Address||Description||Data||Bits and such|
|BASE + 0||Board Identifier||ASCII 'T' Read Only||ASCII 'T' equals hex 0x54|
|BASE + 1||reserved||Read Only|
|BASE + 2||Jumper status||Read Only|| Bit 0: Jumper 1 ('1'=on, '0'=off)|
Bit 1: Jumper 2 ('1'=on, '0'=off)
|BASE + 3||Interrupt Control Register||(R/W)|| Bit 0: PortC bit 0 connects to IRQ5|
Bit 1: PortC bit 1 connects to IRQ6
|BASE + 4||Data Direction Register||(R/W)|| Bit 0: PortC direction ( '1'=output, '0'=input )|
Bit 1: PortB direction ( '1'=output, '0'=input )
|BASE + 5||Port A Data Register||(R/W)||Bits 0-7 correspond to PortA pins 0-7|
|BASE + 6||Port B Data Register||(R/W)||Bits 0-7 correspond to PortB pins 0-7|
|BASE + 7||Port C Data Register||(R/W)||Bits 0-7 correspond to PortC pins 0-7|
|Base + 0x100||off||off|
|Base + 0x108||off||on|
|Base + 0x110||on||off|
|Base + 0x118||on||on|
|JP3||Port C inputs||Port C outputs|
|JP4||Port B inputs||Port B outputs|
|Note:||When Port B or Port C pins are configured as outputs, the pins will reset to the low or zero state on reset.|
|JP5||Outputs set to '0'||Outputs set to '1'|
3 Product Notes
3.1 FCC Advisory
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly (that is, in strict accordance with the manufacturer's instructions), may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class A digital device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the owner will be required to correct the interference at his own expense.
If this equipment does cause interference, which can be determined by turning the unit on and off, the user is encouraged to try the following measures to correct the interference:
Reorient the receiving antenna. Relocate the unit with respect to the receiver. Plug the unit into a different outlet so that the unit and receiver are on different branch circuits. Ensure that mounting screws and connector attachment screws are tightly secured. Ensure that good quality, shielded, and grounded cables are used for all data communications. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The following booklets prepared by the Federal Communications Commission (FCC) may also prove helpful:
How to Identify and Resolve Radio-TV Interference Problems (Stock No. 004-000-000345-4) Interface Handbook (Stock No. 004-000-004505-7) These booklets may be purchased from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.
3.2 Limited Warranty
Technologic Systems warrants this product to be free of defects in material and workmanship for a period of one year from date of purchase. During this warranty period Technologic Systems will repair or replace the defective unit in accordance with the following process:
A copy of the original invoice must be included when returning the defective unit to Technologic Systems, Inc. This limited warranty does not cover damages resulting from lightning or other power surges, misuse, abuse, abnormal conditions of operation, or attempts to alter or modify the function of the product.
This warranty is limited to the repair or replacement of the defective unit. In no event shall Technologic Systems be liable or responsible for any loss or damages, including but not limited to any lost profits, incidental or consequential damages, loss of business, or anticipatory profits arising from the use or inability to use this product.
Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping. Please, contact Technologic Systems to arrange for any repair service and to obtain repair charge information.